ADVERTISEMENT

How to Setup Wireless Security Alarm System

ADVERTISEMENT

-image-

1 System Introduction

Wireless GSM intelligent anti-theft electronic alarm system is an innovative wireless mobile intelligent warner integrating GSM digital signal processing techniques and imported STC microprocessor, and a variety of technologies including digital voice announcer, English SMS, learning code, etc.

In addition, this alarm system is highly automatic, giving automatic voice or SMS alert in the event of emergency without intensive manual settings required. Features of stability, reliability, safety, and humanizing control enable it to be widely used for alert in shops, convenience stores, offices, villa as well as residential communities.

3 Technical Parameter
-image-

4 Factory Default
-image-

5 Installation
Main Unit Installation

Be careful to keep it away from large metal objects or household appliances which may cause high frequency interference, as well as barriers such as reinforced concrete walls and fire doors.

-image-

SIM Card Installation
1: Push out the SIM card socket as the open direction.
2: Fit the GSM card into the card socket properly.
3: Push the card socket as close direction until it is fit firmly.

-image-

6. Main Unit Settings

Prompt Message

-image-

Factory Reset

First switch off the backup battery and cut off the power supply, press and hold the button [Set] on the top of unit,then turn on the power adapter; 3 seconds later, the buzzer emits a long “beep” and all the LED indicators go on but go off instantly; at last you can release the button. That’s mean all its settings cleared and return to its factory settings successfully.

Enter Setting

In the status of disarm, press and hold [Set]; 3 seconds later, the main unit emits a long “beep”, [Arm] indicator flickers and the main unit enters the setting status.

In the status of settings, as long as keeping the status of setting ([Arm] indicator flickers), you can program different settings repeatedly. During setting, however, if you stop setting operation for over 30 seconds, the main unit will exit from setting mode automatically and return to the status of disarm.

DO NOT MISS TO READ  How to Activate ANNKE IP Camera via Web Browser without DVR/NVR

Exit Setting

After setting is finished, all the indicators of the defence zones is off but only [Arm] indicator flickers; press [Set] for 3 seconds,the main unit exits from setting. [Arm] indicator goes off, the main unit returns to the status of disarm.

Code Pairing by Remote Control

Cautions: when deleting remote control, all the remote controls would be deleted.

7 Remote Control Programming

All the programming of the main unit are completed by key operations on a phone or send SMS commands, which shall dial GSM card number of main unit first.

-image-
-image-

SMS Instructions

-image-

Change Password

In the status of remote control programming, directly enter the address code [30]/[31] by phone keys, enter the 4-digit new password, at last add [#] to confirm. The main unit emits a long “beep” tone, indicating the operations are successful.

Operation password: -image-

Illustration: “X” indicates the new password; for example, change the factory default (8888) of programming password into the new password: 0000.

-image-

SMS Command: 8888310000#

Operation Password: after dialing the SIM card number by mobile phone (or fixed phone), if you enter the operation password (factory default: 1234), you can only perform the operations including arm, disarm and monitoring by remote control.

Programming Password: after dialing the SIM card number by mobile phone (or fixed phone), if you enterprogramming password (factory default: 8888), you can only perform the following settings including voice call, SMS receiving phone number and functions.

Cautions: the operation password and the programming password can not be set to the same numbe

Phone Setting

*Voice Call

When it is set to alert through voice call, the main unit can send warning voice message to 6 phone numbers, (for example: defence zone 5, balcony alarm, this is……) .

DO NOT MISS TO READ  How to Enable Smart IR in Analog HD Camera

In the status of remote control programming, enter the address code [51]~[56], enter the phone (fixed phone) number and then enter [#] to confirm. [51]~[56] represent the address codes corresponding to voice alarm-receiving phone numbers from the first group the sixth group.

-image-

Illustration: “X” indicates the set voice alarm-receiving phone number; set 0755-88824002 to be the second voice call number.

-image-
SMS Command: 888852075512345678

Delete the third group of voice call number. -image-

SMS Command: 888853#

*Message Receiving Phone Number

When it is set to alert through message, the main unit will send alarm SMS to three phone numbers, (for example: defence zone 5, balcony alarm).

-image-

Illustration: “X” indicates the set message-receiving phone number; set 13811111111 to be the first message-receiving phone number.

-image-

Delete the first message-receiving phone number.

-image-

SMS Command: 888857#

Defense zone Programming

In the status of remote control programming, enter the address code [60], first enter the defence zone number by [1~6], then enter the defence zone type by [1~4], then the defence zone location by [1~6], and then select if the alarm sound is enabled by [0/1], at last add [#] to confirm.

Operations: -image-

Notes: “A” indicates the number of defence zone; “B” indicates the type of defence zone; “C” indicates the location of alarm; “D” indicates if the siren sounds.
A: Number of defence zone: [1~6] corresponds to defence zone 1 to defence zone 6respectively.
B: Type of defence zone: [1] real-time, [2] 40 seconds delay, [3] 24 hours a day, [4] bypass.
C: Installation Location: [1] help alarm, [2] fire alarm, [3] gas leak, [4] door lock alarm, [5] hall alarm, [6] window alarm, [7] balcony alarm, [8] perimeter alarm.
D: Type of siren: [0] sound-off, [1] sound-on

DO NOT MISS TO READ  [2020-October] Xmeye Super Passwords List

-image-

SMS Command: 8888601321#

Defence zone at Home

In the status of setting, press the address code [61], enter the corresponding number of defense zone by [1~6] and select [0/1], at last add [#] to confirm.

Operations: -image-

-image-

SMS Command: 88886111#

Operating Siren

In the status of remote control programming, enter the address code [75]; in the operation of arm/disarm by remote control, select if the siren sounds or not by [0/1], then add [#] to confirm. [1]: sounds on; [0]: sound off; the factory default is [0], indicating that it doesn’t emit a prompt tone.

Operations: -image-

SMS Command: 8888751#

Clock Setting

In setup status, use keypad to input [32], then input the two digits [AA] of the present hour (24-hour system), the two digits [BB] of the present minute, and finally enter [#] to confirm. You will hear a long beep and a voice prompt “setting finished”
Operating method: [32]->[AA]->[BB]->[#]
AA indicates: the 2 digits of the present hour.
BB indicates: the 2 digits of the present minute.
For example: set the time as 3:35
Operating method: [32]->[03]->[35]->[#]
SMS Command: 8888320335#

ADVERTISEMENT
Harsha Jayamaha

Harsha Jayamaha

Harsha is an independent writer who is keen on security industry. He also loves to share new ideas and information of security life with readers.

Next Post

Google Seacrh

Sponsored by

Ads

Advertisements by Google

Related Ads

ADVERTISEMENT

Welcome Back!

Login to your account below

Create New Account!

Fill the forms below to register

Retrieve your password

Please enter your username or email address to reset your password.

error: Right Click Disabled !!